2-Way multiprotocol radio unit, with 8 inputs and 8 outputs (expandable to 32 IN-OUT) and 3 service channels (network, tamper and battery). Log with max 512 events. Back-up connection on PSTN (with IF-TL) and GSM (with BT-GSM). Plastic case with tamper.



Power supply 110/230Vac 50Hz / 13,8Vcc, with 4A switching power supply
Battery 12V, 7,5Ah max
Power consumption at 230V 130mA in stand-by (RX mode)
300mA in transmission at max power
Power consumption at 12V: 170mA in stand-by (RX mode)
3,5A in transmission at max power
Range frequency VHF (156÷174MHz)
UHF (430÷470MHz)
Channel spacing 12,5KHz
Radio deviation ± 1.65 Khz
Check battery Continuous monitoring voltage
Stability in frequency 2,5ppm –20 ÷ +70°C
TX power 1/5/10W programmable
Receiver system Double conversion superheterodyne
Receiver sensitivity >12dB Sinad –118dBm
Communication protocol
  • 3 SICEP proprietary protocols
  • 7 compatible protocols
  • REP function for monodirectiona and bidirectionsl devices
  • Anti-robbery management via Radio Pocket
  • Secondary transmission over telephone line for MVS protocol
Audio encodings No. 40 programmable Subtone frequencies CTCSS
No. 15 transponder tones
Input channels 8 expandable to 32
Impedance 100KOhm, configurable NC, NO or double-balanced
Other inputs No. 1 enabling input, 100Kohm impedance
Outputs 8, expandable to 32, Open Collector on GND 100mA max., monostables or bistables
Other outputs
  • No.1 BS output, Open Collector on GND, 100mA max
  • No.1 state output programmable forabnormalityon the controlchannels
  • No.1 +12V output for powering external devices, 800mA max., protected by resettable fuse
Check battery Continuous monitoring voltage
Test dynamic battery Yes, programmable each 1/5/10/20/30 days
Control voltage Check continuous of voltage
Opening the case Test continuous for opening case
Antenna cut
  • Check for removal of antenna (only for DC grounded antennas)
  • 2 types for check antenna efficiency
  • RS-485 for I/O expansions and BT-GSM
  • RS-232 for programming and update the firmware
  • USB for programming
  • Interface for PR-G1 programmer
  • Antenna connector type “N” 50 ohm
  • Removable terminal block
PSTN module management Yes with optional interface
GSM module management Yes, with optional interface
LED Signals Mains, low battery, receiving a valid signal, TX, Rep mode, power
  • Calendar clock
  • Log with 512 events on non-volatile memory
  • Thermal protection on transmitter radio
  • Power supply protection on therminal board
  • Firmware updatable via PC
  • Configuration software Sicep Connect with interactive pages
Operating environment temperature Temperature from -10° to +55° C; Humidity from 20% to 80%
Case Protection IP 30
Dimensions 31 x 29 x 9,5 cm (without antenna)
Weight 1,45 Kg without battery, 4,25Kg with 7,2Ah battery
Optional kits
  • PSTN line module interface
  • Expansions I|O
  • RTX module
  • Remote contoll



To view the manuals, you need to log in.
CLICK HERE if you are already logged in otherwise log in


To view the firmware it is necessary to login.
CLICK HERE if you are already logged in otherwise log in



IRS-8B.V Power 230Vac, VHF, 10W power, canalization at 12,5KHz, 156÷174MHz Frequency
IRS-8B,U Power 230Vac, UHF, 10W power, canalization at 12,5KHz, 430÷470MHz Frequency


ANT-S158 5/8 omnidirectional antenna.
ANT-S455 5/8 omnidirectional antenna.
BT-EX8/3 Expansion module 8 inputs – 8 outputs.
IF-TL Telephone interface card.
KIT-AG918S Kit antenna GSM Dualband (900MHz/1800Mhz)
IRS-K2 Anti-robbery kit.
BT-KT/2 Bidirectional 2-channel remote control.